Home > Packard Bell > Packard Bell Post Error Codes

Packard Bell Post Error Codes

Contents

You also may have had sector failure in the start of the Hard Drive, this is what may be causing the Beeps - the hard Drive is not detected by the pctek28-12-2007, 08:28 AMmakes a continuous beep sound. There is one more program I'm looking for, got the link someplace :D this may fix the boot problem. If not then it could be a Blown Mobo. check over here

Or RAM utterly covered in huge amounts of fluff. pctek30-12-2007, 07:54 PMThere is also no differnces in the beep i get when i try to start up, still the same as before. Reset CMOS. You may need the Image Burn from My sig - simply put in a blank CD, open the program, locate the ISO file you downloaded and click the burn button on

Packard Bell Error Codes

As I am looking at upgrading in the near future and don't like to buy your No1! Complementary Content BIOS ( Basic Input and Output System ) - Error Codes/Beeps - Entering BIOS/CMOS Software stored in a Read-Only Memory (ROM) chip on the motherboard (CMOS). The system returned: (22) Invalid argument The remote host or network may be down. Thats the trouble with "brands" - its pot luck what brand components are put in them.

wainuitech28-12-2007, 03:49 PMOkay - read the original post to fast - sorry, thought it was only detecting the CD. Yet boots and runs fine from that CD. Earlier computers use a series of beeps. When it looks for the hard drives boot record the result is ok and then go no further. :rolleyes: :annoyed: thats completely different then, if there is nothing in either drive,

Use these codes before referring to the other codes when they occur. Packard Bell Beeping On Startup If lights come on then power supply is good. sloaphoneJan 18, 2013, 1:25 PM yeah,agree,. Is it the graphics card?

While wearing eye protection, use canned air or the end of a vacuum cleaner to remove dust from vents, preferably outdoors. Temperature is critically high. Reduce further if issue persists. so i restarted the computer and started randomly pushing the 2 digit f buttons, one of them eventually took me to MS recovery program where i tried a non-destructive recovery of

  1. spaceman881531-12-2007, 09:44 AMI think its time he took it to a tech personally.
  2. If it continues again, then I suggest checking the RAM, which might mean replacing them.
  3. as i have had problems with it before.
  4. Post 32 spaceman881529-12-2007, 05:52 PMIf its scanning the PC, and YES it does take a while, it should find any damaged sectors If there are any within the first 30 minutes,
  5. flank21Nov 22, 2009, 12:23 PM had a similar situation, I just received a computer after doing a repair, and went to power it on and got the continuous beeping, looked up
  6. Support Forum Join the conversation!

Packard Bell Beeping On Startup

but i do no use the floppy drive anyway. Type in chkdsk /r (Note space between k /r) press Enter. Packard Bell Error Codes HOPEFULLY when it reboots you will have your Desktop all up and going, you may need to reactivate the OS, thats a phone call to MS on their activation window, and Packard Bell Continuous Beep Clean fans.

What this does, and it's how I test some hardware in the workshop, is boot from the Live CD, it runs through and detects all hardware, if every thing loads OK check my blog when asked, enter the product key thats on the side, it will reboot several times this is normal, it will take approximately an hour. Reset CMOS. As I am looking at upgrading in the near future and don't like to buy your No1!

Thermal 4.4 An MXM over temperature condition has been detected. With the development of the Extensible Firmware Interface (EFI) environment, many HP Pavilion and Compaq Presario computers built in 2011 or later can use blinking LEDS to identify hardware component reporting If there is a hardware problem, you would normally have problems with the bootable CD as well, as in it wonít run either, but you are saying they run fine. http://davegaubatz.com/packard-bell/packard-bell-bios-error-codes.html Normally in the workshop I would use a Live Linux CD to do this, if you have one then use that.

Cheers, KK P.S. Before troubleshooting for startup codes, it is important to remove any dust that might have accumulated. Lets recap - The PC boots fine and runs from the Knoppix CD.

If still no luck, the motherboard is probably failing.

Its an ISO file, so burn as per the Knoppix CD, and boot from it. wainuitech28-12-2007, 01:13 PMCould also be a stuck key on the keyboard. If the problem is not resolved, remove other accessory cards, and replace the graphics card or system board. Reset CMOS.

Replace affected component. Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... POST Beeping Error General Codes Bad Motherboard - 1 long and 1 short beep Disk drive related problem / Video card problem - 1 short beep then nothing happens Bad video have a peek at these guys Caps Lock/Num Lock LED Component tested Error condition Corrective action LED blinks one time CPU CPU not functional Reseat the processor.

wainuitech28-12-2007, 06:39 PMThe part where i said the cd and floppy drive is not found means it cannot find the boot record, which should say that anyway because there is nothing Try removing each card one at a time and restarting the computer. I would like to thank you wainuitech for all the help you have provided. note: The following codes can vary depending on BIOS version.

Test known good component. Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading... We guarantee only CLEAN Ads without any pop-ups, pop-unders etc. Check each individual memory module and swap slots.

All Rights Reserved Tom's Hardware Guide ‚ĄĘ Ad choices PC World Forums > PressF1 > Computer Beeps when turned on and won't boot PDA View Full Version : Computer Beeps when Check for and reseat loose memory modules. Those two events contradict one another.???? :confused: Any way Running the standard repairs like you did, donít always work, so normally if thatís the case its time to reinstall the OS. This page helps to explain what the error message or audio beeps mean.

It comes up with an error: ERROR: Cannot unite read-only media and initial ramdisk! What does the PC do if you try to boot it without the hard drive attached?